Відео

I have a 2015 model...... complete garbage it leaves me stranded all the time... fueling issues.. one thing after another. Afraid to ride alone. Every KTM I have owned has been a pile, I will never buy another one. I'm going to get a Yamaha because they do not break down

I can upload from PC directly to GPS, KMZ or KML formats???

So I just got a 2016 1290 sat. I was doing slow speed and it wouldn’t start back up for about 30 minutes could that be fuel pump related?

Is the power on permanently or only at ignition?

This is very helpful. I am looking into buying a 2016 right now. It will be my 3rd KTM. I like how easy they are to maintain and work on. My former bikes were a 690 SMC and an SD R 990. Both crazy bikes and super engaging. Thanks for all the info!

fuel consumption ???

Great video. I live about a half mile from where you got on the causeway in Mandeville. I used to cross it everyday for work.

Hi, followed your steps for installing the front wheel with calipers. When grabbed the front brake there was no resistance, yet the calipers were tight on the rotor. After a few pumps of the brake handle the resistance came back but the brake pads are tight against the rotors and I can't move the front wheel. Any suggestions? Thx

Are the 990 Adv clutch plates interchangable with the 890 adv ??

I went that route on my GSX-S1000 and ordered a Quantum pump. No good. The Quantum pump would keep flowing even after pressure disconnect. Horrible fluctuating idle and the smell of fuel all the time. It worked but these were the symptoms of the Quantum. Ended up returning it and buying an OEM pump. No issues what so ever. Stay away from cheap alternatives. The OEM will last another 40k. The quantum will not and the work needed to replace again will be needed.

Luv to see riding in my area, I have been on most of those roads so it was good to regonise places. I am always looking for new places and the roads in WV are amazing, I doing it on a Harley RG so try to avoid gravel roads where possible lol Think I will get out that way this week that pie looked delicious :)

Perfect, thank you.

I just purchased the SPYDER PRO 2700 psi unit and I must say, it's a nice little unit. It is replacing my Karcher K5 which was a total failure. It was my fourth Karcher home unit over the years and they all were complete crap that failed quickly. The SPYDER PRO 2700 however is a really nice little unit which houses all the included accessories (Spray Tips, Foam Cannon, Hoses, etc) directly on the side of the unit. The stainless steel wand is very nice. The foam cannon is OK and performs great, but I upgraded mine to the best one on the market today, The Griot's Garage BOSS Foam Cannon. You can also upgrade your spray gun to the a short "stubby" gun for the unit. McKillian's is the best deal on-line (Amazon) right now in my opinion for the stubby spray gun. It's a really nice spray gun for a reasonable $60 price and going with the short or "stubby" gun makes the unit much easier to use, especially when vehicle detailing. Stainless steel swivel fittings, and it's a solid commercial style, heavy duty spray gun. McKillians also make a fantastic stainless steel quick connection kit with all the fittings you need for around $30 which is a really good deal for connectors and fittings of this quality. McKillian's make very stout, solid, well made accessories for your SPYDER PRO 2700 or other SPYDER pressure washer. I use my SPYDER PRO 2700 PSI unit primarily for vehicle detailing which is why I added the extra accessories from McKilian's which made my whole unit just as good as the higher end units for about 1/2 the price. I think anyone who purchases the SPYDER PRO 2700 unit will be very happy with their purchase. It's the upper end unit on the SPYDER range of pressure washers but I did my research pretty extensively and it's well worth the extra couple of dollars to purchase the SPYDER "PRO" units. The PRO units are the nicer pressure washers in the SPYDER range. If you decide to add on the high end commercial grade accessories from McKillian's, you will be very happy indeed and it should give you many years of great service if you are only using this unit once or twice a week on average such as car washing, etc. One recommendation I would highly recommend is that you run a cleaner and protector through your pressure washer once per year. This is a product available on-line for between $9 and $15 per can. It's a cleaning solution and seal conditioner which protects your unit from premature wearing out. It's well worth the price once a year to protect your investment.

Now we know why maintenance cost a fortune on those 990 ADV’s if it’s done by the dealer.

What kind of MPG are you getting with this kit installed?

« She will never win a beauty contest » 😂😂 So do I ! 😅👍✌️

So i the dealer ship I work has 2016 ktm 1290 with 5 k I am looking at snagging is their anything you would recommend me to look for

I hate install videos. I don’t hate this one.

how do u diagnose a faulty starter torque limiter?

Still your best series, never get tired of watching it.

Hey bro are you in va

Che casino ! Per un semplice cambiamento di candele , devi smontare mezza moto.

Great video. Thank you. Although I have been changing wheels on my motorcycles for close to 30 years, it is a first on my 2023 ADV. Great point on the ABS sensor. Just one comment, I believe you need to tighten the main axle before you tighten the pinch bolts. Thanks again

Does it have traction control? Like can i wheelie it?? I hope its only abs

I'd be shocked if you noticed in gain in power, but kudos to Rottweiler for bringing products to market that will prevent you from dusting your motor!

Hello, do you know if I can mount the adventure T support and panniers on a 2024 adventure R? thank you !!!!!

I have a bunch of stuff in the way of my rear cylinder can chain tensioner, how did u end up getting to it? There’s some black box on mine I didn’t see on yours but it won’t move

Hi. I'm loving these videos. I'm looking to do the valves on my GT. Do you have a video for removing the Throttle bodies so that I can get to the Cam Covers?

I found out that the dongle failed. Rottweiller sent me another one no questions asked but it took 3 months to get here since my motorcycle is in Ecuador.

.... I'll always take rain over heavy smoke, especially what you guys rode through.

Always seem to end up right back here on your channel when servicing my 1090 ... swapped the rim seals this last weekend. Not hard by any stretch, but my advise to people is to take their time and do it right. It is tedious, but if you use a lot of soapy water and work about 3-4" at time the seal seats without much of a fight. I also used an automotive trim tool to seat the seal into the rim.

Be sure to loctite your compression unit and pull up on the cartridge all the way through to make sure they are bled all the way

I just ordered a 1.85-21/2.5-18 set of wheels with some motoz i/t tires expecting to use the oem wheels for highway use & the new wheels for offroading. I can't tell if that's going to be a huge pain in the a$$ or not 😅🤣

XT2 would be good for future proofing? No? Garmin is clearly going to move onto the XT2 and support for XT will fall off? That’s just my speculation.

i just orded the touring plus version, is this the one you have? i orded it because of your review, iam 6.2 and the oem just sucks, causes allot of tourbulance on my helmet , i firdt thought my helmet eas crap, but when i bought a 500 dolara toruing helmet , still same problems.

Great video! One question: do you need to remap the engine software after deleting cat?

Thanks for this. Just finished up a 23' 890 Adventure. A few notes which may be 23' specific. If you are re-using the original bolt that held the cat on to secure the mid pipe it's 15 Nm. The shift rod bolt is 10 Nm. The 3 T-45 for the footrest bracket side stand all need loctite. I wasn't able to get to the right side cat bolt behind the brake lever with a ratchet and socket and had to use a 10mm open end ratchet.

Your videos are great! I have an issue, the torx screw at the top that holds on my tank spoiler that goes into the tank just spins because the stud in the tank is spinning. Any thoughts on how to get it out without drilling out the torx screw?

i bought one last year, they have depreshiated like a rock and you can get one for well under 10k now. few things: if your battery voltage dips it will pull up an error for the front brake light switch and tear you out of cruise control. got one of those antigravity batteries and it does that constantly. the luggage isn't great, goofy shape and plastic latches are bad. they would be fine for a top loader but as a side loader its hard to tell if they have latched properly, they can also half latch and fly open on the freeway. otherwise good bike. i like how the windshield adjusts, just pick it up and move it, dont have to stop or have an electric mechinisam. dont know why they dont use it on the adventure.

Great video thanks. I thought I'd done well getting 22000 miles out if my chain and sprockets, I could have probably squeezed a bit longer but quite a few tight spots now and I have a big trip planned in a few weeks. Not sure if I'll need a new chain slider. What's your chain maintenance routine as your getting good life form your chain and sprockets. 👍

Hooligan touring machine✊🔥

Can we just remove the right side? Or left one at a time?

Mapping??

Aren't you glad one day all this archaic mechanical stuff is going to be replaced by frictionless electrical drive trains? battery technology and Eylon Musk might eventually compete in this field...

I had one of those! Could get a little over 50 mph laying down on it! Lady pulled out in front of me.... smeared me and the bike. Pulled the front end out, and drove it to the Honda dealer, and bought a twin star... still had a cast on my arm, and drove it home! Good times!

Why not use the original Ktm foam filter insert? I've been using it since 2019 without any issues.

You're a real one Mario. Just ran into this with my 2018 after 6 years... thanks for the guide. Hope you're healing up good!

Just got mine and it doesn't have any instructions or anything